About company
News
On-line order
Contact
    
    
    
    
    
    
Towers
Masts
ONLINE ORDER »  
CONTACTS:

Joint-stock company Ltd.  “ТAKERA”
Vilnius, Lithuania

Vejo 1
Tel./fax. +370 (5) 2352906
E-mail: takera@takera.eu ., info@takera.eu

Representative Offices of the company  “ТAKEPA
Moscow, Russia
Tel.: +7 (495)-7826242,
        +7 (926)-2070573
Fax.: +7 (495)-7826242,
E-mail: info@takera.eu, takera@takera.eu

Representative Offices of the company  “ТAKEPA
Kaliningrad, Russia
Joint-stock company Ltd. “TAKEPA” 
Bolnichnaja str. 24-33
Tel./fax. +7 4012 538463
E-mail: takera@takera.eu ., info@takera.eu

 

 
Home  »  Communication masts and towers  »  Masts
   Unified aluminium collapsible masts МАР/800, height 5-40 m
   Unified aluminium collapsible masts МАР/941, height 41-107 m
   Unified steel collapsible masts МОС/330, height 5-40m
   Unified steel collapsible masts МОС/630, height 5-70 m
   Unified steel collapsible masts МОС/1000, height 30-120 m
   Unified steel collapsible masts МОС/1200, height 50-160 m
Steel masts of type МОС/630 height 5-70 m

Application

Masts are used for provision of radio-relay communication and/or telecommunication.

Technical features

Masts with braces from truss sections of triangular cross-section and side of 630 mm.
Height of mast: Н mах = 70м, Н min  = 5 m.
Other: Н = Н min + 5хn, where n = 1, 2, 3...7.
 
Positioning

The lowest ambient temperature down to –40 С;
Black ice of the 3rd zone;
Wind load up to the 4th zone;
Load of 4 antennas of 1,2 diameter at the upper mark.

Design standards

According to SNiP (Building Norms and Regulations).

Structure

Steel bolted structure made of 5 m long sections. Strips are made from round cross-section steel profile (yield strength 245 N/mm2). Diagonal and horizontal elements are made from cold rolled angle (yield strength 245 N/mm2). Structures are made according to SNiP (Building Norms and Regulations) and company standard ĮST8671693-2002.
Trusses for braces are made from hot galvanized steel wire. Number and cross-section of braces is subject to height of masts and antenna load. Outside the mast there are stairs with safeguarding profile and special brackets for cable fastening.

Anticorrosive coating

All mast elements undergo hot galvanizing. Depth of coating is not less than 90 micrometers, for fasteners and trusses – 40 micrometers.

Signal paint

Adjusted with the customer. It is made by the joint-stock company Ltd. UAB “Vilniaus universaliųjų metalo konstrukcijų gamykla” at the factory. Painting in two layers: the first – epoxy priming, the second – polyurethane paint. Depth of the coating is not less than 120 micrometers.

Standard delivery of materials

Set of structure elements and necessary fasteners. Trusses of braces of necessary length with reserve as well as tightening devices. Assembly and cable stairs have elements for their fastening inside the mast. All materials are labelled and packed for transportation to the place of assembly.

Technical details of mast

Height of mast Н, m

5

10

15

20

30

40

50

60

70

Distance to anchors of braces, m

2,5

5

8

10

16

21

27

34

40

Zone of wind loads

IV

 
© 2005 Web solutions: Infosistema